• Welcome to Jetboaters.net!

    We are delighted you have found your way to the best Jet Boaters Forum on the internet! Please consider Signing Up so that you can enjoy all the features and offers on the forum. We have members with boats from all the major manufacturers including Yamaha, Seadoo, Scarab and Chaparral. We don't email you SPAM, and the site is totally non-commercial. So what's to lose? IT IS FREE!

    Membership allows you to ask questions (no matter how mundane), meet up with other jet boaters, see full images (not just thumbnails), browse the member map and qualifies you for members only discounts offered by vendors who run specials for our members only! (It also gets rid of this banner!)

    free hit counter

Search results

  1. Terrance

    Trailer Bolt Pattern <Glastron GT187>

    Hard to find a 5 bolt 14 inch rim for your trailer, other than a auto parts o or trailer sakes & parts store.
  2. Terrance

    Trailer Bolt Pattern <Glastron GT187>

    Just found my answer....see picture of trailer specs...below. 5-4.5 inch
  3. Terrance

    Trailer Bolt Pattern <Glastron GT187>

    Hello. Our boat...2015 Glastron GT187 19.5 feet. I’m wondering if anyone with a single axle Glastron steel painted boat trailer with tire size 205/75/14 Knows the chrome rim bolt patter. I might replace the rim and tire, rather than just the tires. Thanks in advance. Terrance
  4. Terrance

    Swim platform mat

    Thanks for the suggestion.
  5. Terrance

    Swim platform mat

    Thanks for the advice.
  6. Terrance

    Swim platform mat

    Hello Jet Boaters. I have a Glastron GT187 with a nice swim platform. I noticed after 5 years of usage that my swim platform mat is starting to lift around the edges. What is the best adhesive/glue to use if I want to repair it and keep it from lifting more? Thanks Terry "The Honey Badger"
  7. Terrance

    Impeller separating from shaft.

    The dealer checked motor mounts and alignment. Replaced drive shaft, wear ring, and miscellaneous parts under warranty. im back in the water for a new season, with fingers and toes crossed. All good so far.
  8. Terrance

    Bilge pump

    Hi Luc, Thanks for the advice. I will take a look at the angle of the pump and re-adjust. merci mon ami!
  9. Terrance

    Bilge pump

    Anyone know how to get this bilge pump to stop pumping? It automatically sucked up rain water till the bilge was empty and never turned off.
  10. Terrance

    Bilge Pump will not shut off.

    Hello all. I came home from work today and the bilge pump was running even though the power on the boat is off. It did rain heavily this morning however there is no water in the hull now. It seems like the auto on/off switch is stuck. I can disconnect the bilge at the connection point and it...
  11. Terrance

    Check Engine message

    The kill switch is located about four or five inches in front of the throttle, on the side of the boat, not on the dash. There is a small knob about a half inch long. There should be a little plastic clip (lanyard). attached to it. Normally a red string is tied the the lanyard clip. It’s meant...
  12. Terrance

    Check Engine message

    Hey Schmelkzy. Could be your starter or the voltage regulator. Perhaps the ignition switch? Cheers Terry
  13. Terrance

    Check out these Red heads

    Very Nice...well Done Ronnie!
  14. Terrance

    BRP Rotax 4tec flush relocate

    Hi Dean. Thanks for the reply. Very helpful. I might just do the clip on garden hose mod for now. My son can do the “twist and shout” hooking it up...lol Cheers Sent from my iPad
  15. Terrance

    BRP Rotax 4tec flush relocate

    Hello Dean Just wondering where you ordered the relocation flush kit. I have the same set up as you. RE: Boat on a lift after use. Thanks Murf
  16. Terrance

    Impeller separating from shaft.

    We have a GT 187 150HP Third time the impeller seems to slip off drive shaft and is separate from engine. Engine runs fine. Impeller is free wheeling with no propulsion. Boat is at the dealer. Anyone have this happen? Third time for a repair? Thanks for any ideas. Terry
  17. Terrance

    250 Hours on GT187

    Hello Glastroners. Anyone out there have over 250 Hours on GT187 1.5 litre? Mine just turned 250 hours and check engine light can on.wondering if this would be sensor schedule maintenance or another O2 oxygen sensor to replace. Thanks Terry
  18. Terrance

    Speedometer

    Hi Brad. Im about the same. Pending the number of passengers. 35 is tops.
  19. Terrance

    Other Yamaha's? Motorcycles anyone?

    2003 Silver Edition Silverado Roadstar...
  20. Terrance

    Let me see your boat names.

    Here is where we planted the name...
Top