ripler
Jetboaters Captain
- Messages
- 923
- Reaction score
- 1,355
- Points
- 227
- Location
- Just south of Pittsburgh
- Boat Make
- MasterCraft
- Year
- 2021
- Boat Model
- Other
- Boat Length
- 20
So I finally talked the wife into a V-drive and we are putting our boat up for sale.
I'm located south of Pittsburgh,PA.
My boat is a SX210 but with an aftermarket tower and my trailer is galvanized, which was a 750.00 upcharge. The boat has never been left in the river, it gets stored in my garage and trailered everywhere. My garage also never gets anywhere near freezing so the boat has never been in cold weather. After every outing it gets wiped down and cleaned with hot sauce as needed. I have a full Yamaha cover and also the original shipping cover. I am the original owner.
Here's the list of mods I've made
-Aerial Airborne tower with 2 board racks
-Clarion M303 reciever
-Clarion stern remote
-Sirius XM module
-Clarion EQS755 equalizer, this allows me to control the volume between the tower speakers and the interior speakers, it allows sub woofer volume control also
- 4 Rockford Fosgate 6" interior speakers
- 1 Rockford Fosgate 10" sub
- 2 Wetsounds REV8 tower speakers with swivel clamps
- 2 Rockford Fosgate R600-4D amps, approx 1600 watts total
- 2 batteries with battery switch
- Dual channel marine battery charger
- RGB lights everywhere, with remote control and sound activated control module
-Black Tip traction mat on swim deck and anchor door, I also have a bunch of extra pieces because they messed up a piece in 2 of my orders and they didn't want the old ones back, s²o essentially I have 2 extra sets.
- Cobra EZ locks on clean out ports
-The trailer came with brakes on 1 axle from the factory, PA requires trailer inspections and brakes on both axles, so I added brakes to the second axle, the inspection is good in PA until July 2021.
- Stoltz bow roller
-Keel guard
- New bearing buddies installed before this season
-USB charging ports in glovebox
-USB and 3.5mm ports in glovebox to interface with radio
-USB charging ports, cigarette lighter style outlet and battery voltage display added near throttles
I have brand new bunk boards in my garage waiting to be installed, the boards on the trailer don't need replaced, but it's easier to install a new carpeted bunk than it is to rip off and replace the existing carpet. I have a Attwood SS scupper waiting to be installed, it's not needed on my boat since the scupper is above the waterline, but I'm changing it anyway.
-I also have Yamaha YDS diagnostic software and cable to troubleshoot if needed, I've never used it
-I also have a shop manual on CD
I'm asking 25,000.00.
I'm located south of Pittsburgh,PA.
My boat is a SX210 but with an aftermarket tower and my trailer is galvanized, which was a 750.00 upcharge. The boat has never been left in the river, it gets stored in my garage and trailered everywhere. My garage also never gets anywhere near freezing so the boat has never been in cold weather. After every outing it gets wiped down and cleaned with hot sauce as needed. I have a full Yamaha cover and also the original shipping cover. I am the original owner.
Here's the list of mods I've made
-Aerial Airborne tower with 2 board racks
-Clarion M303 reciever
-Clarion stern remote
-Sirius XM module
-Clarion EQS755 equalizer, this allows me to control the volume between the tower speakers and the interior speakers, it allows sub woofer volume control also
- 4 Rockford Fosgate 6" interior speakers
- 1 Rockford Fosgate 10" sub
- 2 Wetsounds REV8 tower speakers with swivel clamps
- 2 Rockford Fosgate R600-4D amps, approx 1600 watts total
- 2 batteries with battery switch
- Dual channel marine battery charger
- RGB lights everywhere, with remote control and sound activated control module
-Black Tip traction mat on swim deck and anchor door, I also have a bunch of extra pieces because they messed up a piece in 2 of my orders and they didn't want the old ones back, s²o essentially I have 2 extra sets.
- Cobra EZ locks on clean out ports
-The trailer came with brakes on 1 axle from the factory, PA requires trailer inspections and brakes on both axles, so I added brakes to the second axle, the inspection is good in PA until July 2021.
- Stoltz bow roller
-Keel guard
- New bearing buddies installed before this season
-USB charging ports in glovebox
-USB and 3.5mm ports in glovebox to interface with radio
-USB charging ports, cigarette lighter style outlet and battery voltage display added near throttles
I have brand new bunk boards in my garage waiting to be installed, the boards on the trailer don't need replaced, but it's easier to install a new carpeted bunk than it is to rip off and replace the existing carpet. I have a Attwood SS scupper waiting to be installed, it's not needed on my boat since the scupper is above the waterline, but I'm changing it anyway.
-I also have Yamaha YDS diagnostic software and cable to troubleshoot if needed, I've never used it
-I also have a shop manual on CD
I'm asking 25,000.00.
Last edited: