I broke my pee hole.....

[MIKEP]

I was scrubbing my hull with a brush and snapped off one of the valves "pee holes" on the side of the boat!! It doesn't affect the operation, but the stream shoots out further than the other. Cosmetically I would like to replace the valve. Any idea where I would look to get a replacement part??

 

[Mike Serra]

Is this what your are looking for?

https://www.ebay.com/i/391849576921?chn=ps&dispItem=1

 

[Mike Serra]

This is what I found on Yamaha 's parts site:



https://www.shopyamaha.com/parts-catalog/parts/boats?ls=Boat&dealernumber=#/Yamaha/AR240_HIGH_OUTPUT_-_SAT1800CP_-_2015/EXHAUST_3

 

[BlackandTan]

Maybe you should go to the doctor! All kidding aside, I didn't see it on the Yamaha Sports Plaza diagrams. You'll probably have to go to the dealer. May be covered under warranty?

 

[blacksapphirez]

they have aluminum replacements...looks sharp

 

[RightStuff]

This is the discussion I bookmarked because I need to get new ones as one of mine is broken too.
https://jetboaters.net/threads/what-size-hose-goes-to-the-cooling-pee-stream-fittings-10-242-l-s.12470/#post-216006

The only thing I'm not sure on is the hose size, and I haven't crawled in that compartment to verify. Looks like there are 2 options, 3/4" and 3/8", anyone know what the right size is for boats?

 

[Bill D]

Pretty sure it's 3/8". Definitely not 3/4" as that is what the stock bilge pump is.

 

[RightStuff]

Spoke too soon I guess, there also is a 1/2" option as well...

3/4" - http://adaracing.com/personal-watercraft-products/fittings/jet-ski-bilge-outlet-fittings-45-degree/
1/2" - http://adaracing.com/personal-watercraft-products/fittings/jet-ski-sea-doo-4-stroke-water-bypass-45-degree/
3/8" - http://adaracing.com/personal-watercraft-products/fittings/jet-ski-superjet-pwc-water-bypass-fitting-45/

 

[MIKEP]

@Mike Serra thanks man!! It's exactly what I need. Much appreciated!!

 

[AndyD]

So what would you most compare your pee holes to now??

 

[RightStuff]

If anyone comes to this looking for the size to order to replace the fitting for the coolant lines, I just did my yesterday and the 1/2 fitting (45 deg.) from ADA racing fits the coolant line ones.

https://adaracing.com/personal-wate...-ski-sea-doo-4-stroke-water-bypass-45-degree/

I did have to Dremel the holes in the hull a tiny bit for the threads to fit, so just a heads up to anyone else swapping them out. It is also much easier as a 2 person job, hard to align the fittings on the outside while tightening them from the inside.

 

[Van T]

I did three of them on the side of my boat it was definitely hard to do by yourself. The key is to put some sealant underneath them tighten them a little bit let it dry then go back and tighten

 

[jEt_jAk]

Thanks for the sizing help in this thread. Got mine today

Links

ADA Racing Billet 3/4" Straight Bilge Fitting Yamaha Kawasaki SXR Superjet ZXi | eBay

ADA Racing Billet Water Bypass Outlet 1/2 45° Jetski Yamaha Kawasaki GP1200 1100 | eBay

 

[seanmclean]

Thanks for the sizing help in this thread. Got mine today

Links

ADA Racing Billet 3/4" Straight Bilge Fitting Yamaha Kawasaki SXR Superjet ZXi | eBay

ADA Racing Billet Water Bypass Outlet 1/2 45° Jetski Yamaha Kawasaki GP1200 1100 | eBay

Looks nice!

 

[AmesJainchill]

I had these bookmarked just in case as well. Looks like there are a few options?

https://jetboaters.net/threads/bilge-and-pisser-fittings.19496/