• Welcome to Jetboaters.net!

    We are delighted you have found your way to the best Jet Boaters Forum on the internet! Please consider Signing Up so that you can enjoy all the features and offers on the forum. We have members with boats from all the major manufacturers including Yamaha, Seadoo, Scarab and Chaparral. We don't email you SPAM, and the site is totally non-commercial. So what's to lose? IT IS FREE!

    Membership allows you to ask questions (no matter how mundane), meet up with other jet boaters, see full images (not just thumbnails), browse the member map and qualifies you for members only discounts offered by vendors who run specials for our members only! (It also gets rid of this banner!)

    free hit counter

Search results

  1. Y

    2006 SR210 - Engine noise ?

    I have a feeling I will be checking the oil more often. I usually do it a few times per season, not every outing though. Since it is kept in the water July-September I do have my routine. The clean out plugs are left in place but pulled every time I uncover the boat prior to use. I reach in...
  2. Y

    2006 SR210 - Engine noise ?

    ***Update*** Upon winterization my tech found water in the oil: He narrowed down and ID'ed the leak to where the metal pipe enters into the valve cover. It seem that o-ring and gasket below was allowing water through. This was probably the reason for rougher idle it was experiancing this...
  3. Y

    2005 AR230 saga continues, now I have water in the oil

    This forum proved great today! I had my tech winterizing my SR210 today and found milky oil in the port engine. Pulled the cover to the oil cooler and it was not pretty. He looked around a bit more then pulled the valve cover and found exactly what was posted above! I had logged on here to find...
  4. Y

    Rubber Shaft Coupling - anyone replace?

    I have heard the bearings are a lot more common. I posted a thread about an engine rattle before so I installed new plugs and coils and took compression (which all were equal and strong per the service manual). Oil is clean and proper level. I hauled the boat and had my tech pull the pump and...
  5. Y

    Oil Pan Leak

    It solved the issue and never had a drop of oil since.
  6. Y

    Rubber Shaft Coupling - anyone replace?

    I am starting to suspect I might have a rubber shaft coupling that has failed, has anyone replaced this before? Not so much looking for a 'how to', just wondering how common it is and/or symptoms that lead to it being replaced. Part #1 on the diagram below. Thanks!
  7. Y

    2006 SR210 - Engine noise ?

    So....I removed the plugs, all looked 'ok', gap was even on all, no damage. I took compression and it is equal on all four cylinders. I installed new plugs and new coils. Fired it up and the same noise persists. The other engine is just so smooth and quiet. Once you get above 2k it smooths out...
  8. Y

    2006 SR210 - Engine noise ?

    Thanks for your thoughts. The boat is kept in the water so I plan to start with taking compression just to confirm, if all looks well I will install 4 new coils and 4 plugs. If that does not do the trick I fear it might be one of the bearings. I will haul it the pull the pump to see what happens...
  9. Y

    2006 SR210 - Engine noise ?

    I've had this 2006 SR 2010 for a number of years and it is really is in great condition. I noticed the port engine was a bit louder on one of my last trips. I went out today and there is no question now. The starboard is smooth and 'quiet' at idle but the port visible shakes a bit and is...
  10. Y

    Hydrophase Ridesteady - SR210

    Splashed the boat for the season the other day. Tested the Ridesteady system out and worked perfect, this is going to be season number 7 with it, and no issues! Looking forward to a bit of fun as the weather (and water temp) warms up!
  11. Y

    Ignition Coil Gasket - replacement?

    Here are images of what I am missing....
  12. Y

    Hydrophase Ridesteady - SR210

    Finally getting the boat ready for the season. Sent my Ridesteady system in for updates over the winter and received it back very quickly. Just reinstalled the needed components and test ran the boat on the hose and everything looks to be well. Can't wait to get out on the water again and put...
  13. Y

    Ignition Coil Gasket - replacement?

    '06 SR210 - spring prep - changing plugs for the season - unclipped the ignition coil and the bright blue gasket inside the harness somehow sprang free with force and bounced towards the center of the of the engine compartment. I looked all around and and can't find it, I have the plug out in...
  14. Y

    Impeller swap - how difficult/special tools?

    Digging up my old thread and spring is getting closer....so is this project. I have dug around on this forum and on-line and I can't seem to fine an OEM Yamaha tool part number to hold the shaft to remove the impellor. Only thing I found was this from another member YB-06201 but no follow up. Is...
  15. Y

    SR210 Wear Ring/Housing - Yamaha or Aftermarket?

    I have an '06 SR210 that I've owned for about 5 years - A little over 200 hours (bought with 45). There was some minor dings to the impellors when I bought it but did not seem to affect performance. That being said I already have two OEM impellors in hand now but the Wear Ring/Housings have been...
  16. Y

    Aft seat removal - how to?

    Took the seat off this afternoon, simple. As the photo shows above, just three studs. However, my studs were short compared to the ones in the photo as the threads barely extended past the nut. Mine did not have any washers either. Next step is to repair the vinyl, have until June for that though!
  17. Y

    Aft seat removal - how to?

    Thank you, that is exactly what I was looking for! Looking like just 3 nuts/washers to remove and the seat comes off.
  18. Y

    Aft seat removal - how to?

    06' SR210 - My starboard aft seat (that is fixed to the engine hatch) developed a tear in the vinyl this year where the piping is midway across the seat. The cover is always on the boat so the seats vinyl is like it came from the factory, so I would like to remove this piece and have it fixed...
  19. Y

    Impeller swap - how difficult/special tools?

    Since I have owned it the cone bearing has not been inspected, thanks for the tip. Engines have less than 200 hours though. I will also pick up a tool you referenced as well, nice to have one on hand should something happen mid-season and a swap be required. I will dig through the FAQ's on the...
  20. Y

    Impeller swap - how difficult/special tools?

    My '06 SR210 is still running the original housing/wear rings and impellers. They have minor dings that were filed smooth the other year but I was planning to replacing the wear ring/housing and impellers before next season over the winter. How difficult is it to remove/swap the impellers? Any...
Top