Sealing Pump Tunnel

[steelhorse454]

Hey Folks-
I know this has been discussed, but what is recommended to seal the gaps in the pump tunnel?
4200 or 5200 sealant ? Seems like I've seen both used looking at other posts.
Also, what is the best way to pry off the intake grate without breaking it ?

 

[zipper]

5200 is more workable/sandable than 4200. Some have used JB weld, waterweld.

Post in thread 'Pump intake grates- thinking of trying something taboo'

Nov 11, 2017

I currently have everything from the tunnel castings back taken off of the boat. The first round of intake "porting" made so much of a difference I'm doing V2.0 on it right now. A little more aggressive on the transition from the intake tunnel into the wear ring area to smooth the flow. I also cleaned up the vanes and nozzles quite a bit, basically ended up with a pretty big pile of aluminum shavings on the floor of my shop! Just little details that can only help in the efficiency of the pumps. I also painted all the pump parts gloss black, just because I didn't like the bare aluminum...

• swatski

• 

 

[FSH 210 Sport]

I’ve seen people mention this product before.

https://www.amazon.com/gp/product/B00C50GIQI/ref=ox_sc_saved_title_7?smid=ATVPDKIKX0DER&th=1

 

[steelhorse454]

I’ve seen people mention this product before.

https://www.amazon.com/gp/product/B00C50GIQI/ref=ox_sc_saved_title_7?smid=ATVPDKIKX0DER&th=1

Thanks. Being in construction, I know Silkaflex products and they are top notch.

 

[FSH 210 Sport]

Thanks. Being in construction, I know Silkaflex products and they are top notch.

Right on.. if you do a search on this subject, I’m sure you’ll see the threads that have linked this product before

 

[2kwik4u]

Hey Folks-
I know this has been discussed, but what is recommended to seal the gaps in the pump tunnel?
4200 or 5200 sealant ? Seems like I've seen both used looking at other posts.
Also, what is the best way to pry off the intake grate without breaking it ?

Here's what I did. Still holding on strong now 7yrs later.

Thread 'Hero or Zero?......"Resealed" my Jet Pump'

May 26, 2018

OK, Where's @swatski and @gmtech16450yz ?!??! I need someone to tell me I didn't just make a ginormous mess out of my pump housing.

Been fighting a cavitation problem under load when tubing. Might be technique on my part, but still bugs me. Put an L13 cone on a few weeks ago, lost some RPM, but still had the cavitation while turning/tubing. Read lots of talk of resealing the pump to keep cavitation at bay. So here's what I did about it.

Picked up some marine sealant. Finding 3M 5200 around here on a Saturday is like pulling teeth. Loctite has a comparable product, so I'm...

• 2kwik4u
• Replies: 28
• Forum: Yamaha AR190/192/195, SX190/192/195

• 
• 

 

[steelhorse454]

Here's what I did. Still holding on strong now 7yrs later.

Thread 'Hero or Zero?......"Resealed" my Jet Pump'

May 26, 2018

OK, Where's @swatski and @gmtech16450yz ?!??! I need someone to tell me I didn't just make a ginormous mess out of my pump housing.

Been fighting a cavitation problem under load when tubing. Might be technique on my part, but still bugs me. Put an L13 cone on a few weeks ago, lost some RPM, but still had the cavitation while turning/tubing. Read lots of talk of resealing the pump to keep cavitation at bay. So here's what I did about it.

Picked up some marine sealant. Finding 3M 5200 around here on a Saturday is like pulling teeth. Loctite has a comparable product, so I'm...

• 2kwik4u
• Replies: 28
• Forum: Yamaha AR190/192/195, SX190/192/195

• 
• 

Thanks. Very informative !