MissScarlet
Jet Boat Addict
- Messages
- 47
- Reaction score
- 19
- Points
- 87
- Boat Make
- Yamaha
- Year
- 2015
- Boat Model
- SX
- Boat Length
- 19
Anyone try these on a 2015+ SX190?
-
Welcome to Jetboaters.net!
We are delighted you have found your way to the best Jet Boaters Forum on the internet! Please consider Signing Up so that you can enjoy all the features and offers on the forum. We have members with boats from all the major manufacturers including Yamaha, Seadoo, Scarab and Chaparral. We don't email you SPAM, and the site is totally non-commercial. So what's to lose? IT IS FREE!
Membership allows you to ask questions (no matter how mundane), meet up with other jet boaters, see full images (not just thumbnails), browse the member map and qualifies you for members only discounts offered by vendors who run specials for our members only! (It also gets rid of this banner!)
-
Guest, we are pleased to announce that Hydrophase Ridesteady is offering an extra $100 off for JETBOATERS.NET members on any Ridesteady for Yamaha Speed Control system purchased through March 7th, 2025. Ridesteady is a speed control system (“cruise control”) that uses GPS satellites or engine RPM to keep your boat at the set speed you choose. On twin engine boats, it will also automatically synchronize your engines.
Click Here for more information>Ride Steady group buy for JetBoaters.net members only
You can dismiss this Notice by clicking the "X" in the upper right>>>>>
Love my $20 amazon drain plug light
- Thread starter Marvin willis
- Start date
Marvin willis
Jetboaters Admiral
- Messages
- 1,502
- Reaction score
- 918
- Points
- 267
- Location
- Morehead city nc
- Boat Make
- Yamaha
- Year
- 2018
- Boat Model
- AR
- Boat Length
- 24
If it’s the plastic plug like my ar240 then no.
Mystic1906
Jetboaters Lieutenant
- Messages
- 258
- Reaction score
- 207
- Points
- 162
- Location
- Lockhart, FL 32810
- Boat Make
- Yamaha
- Year
- 2017
- Boat Model
- AR
- Boat Length
- 24
What are you using in the new 240?
Greg__Berger
Jet Boat Lover
- Messages
- 32
- Reaction score
- 10
- Points
- 77
- Location
- St. Louis, MO
- Boat Make
- Yamaha
- Year
- 2006
- Boat Model
- SX
- Boat Length
- 23
I went ahead and picked one of these up, but I cannot figure out how to get access to it from inside the hull to wire it. Did you have to take a bunch of stuff apart to get this wired?
- Messages
- 18,651
- Reaction score
- 21,068
- Points
- 1,102
- Location
- Raleigh, NC 27614
- Boat Make
- Yamaha
- Year
- 2016
- Boat Model
- 242X E-Series
- Boat Length
- 24
You will have to take off your clean out tray cover. This isn't hard, just a little time consuming. Screws all around the edge, then hose clamps holding the rubber "pipe" to the bottom of the tray (need thin arms). This thread has some photos:
https://jetboaters.net/threads/removed-fiberglass-panel-over-cleanout-ports.16386/
Greg__Berger
Jet Boat Lover
- Messages
- 32
- Reaction score
- 10
- Points
- 77
- Location
- St. Louis, MO
- Boat Make
- Yamaha
- Year
- 2006
- Boat Model
- SX
- Boat Length
- 23
Excellent, thanks! Seems like changing that plastic scupper valve out at the same time might be in order.
- Messages
- 18,651
- Reaction score
- 21,068
- Points
- 1,102
- Location
- Raleigh, NC 27614
- Boat Make
- Yamaha
- Year
- 2016
- Boat Model
- 242X E-Series
- Boat Length
- 24
Absolutely! If you are down there I'd knock out both at the same time!!!!!
mattster
Well-Known Member
- Messages
- 31
- Reaction score
- 15
- Points
- 57
- Location
- Carmel, IN
- Boat Make
- Yamaha
- Year
- 2012
- Boat Model
- Limited
- Boat Length
- 24
So about a year later, how are they holding-up?
Similar threads
