Completed 2016 SeaDek Group Buy

[Bruce]

Also @Bruce can you put up a sticky or banner asking people to finalize their orders today? That would be helpful. Thanks!

Will do you have a list of the 14? I could send them a message through the forum. I think that would be more likely to get their attention than a notice.

 

[JetBoatPilot]

Ok I will get that to you asap. Thanks!

 

[Rob9550]

If they don't pay, will we still have the numbers needed to get the 30% off?

 

[JetBoatPilot]

Yes no worries there.

 

[chess]

Hey guys and gals. We are at the end of the event and it is closing this afternoon. If your name is in the group buy file you will get to participate but we need to collect payment asap. If you have not paid, which by my count consists of 14 orders, please do so by calling 850-867-1410 and speaking to one of my assistants.

Thank you again for your business and support! My family and staff are grateful!

Also @Bruce can you put up a sticky or banner asking people to finalize their orders today? That would be helpful. Thanks!

Kelly took care of me today

 

[Bryan L]

I gots a box!! So much for lying in a duck blind this weekend.

If I only had @swatski 's cunning, this could have been an epic weekend!

@JetBoatPilot , do you guys stock the RIVA intake rings or would I need to go either through Yamaha or RIVA?

 

[haknslash]

Oh yea!!

 

[Julian]

THANK YOU @JetBoatPilot for another successful group buy event for the members here!

 

[Rob9550]

I know this is off topic but can anyone provide a link to the post or website on hydro-turf removal? I remember someone posting an attachment to help with removal of the old turf and adhesive. Thanks for the help.

 

[Bruce]

I know this is off topic but can anyone provide a link to the post or website on hydro-turf removal? I remember someone posting an attachment to help with removal of the old turf and adhesive. Thanks for the help.

My experience is that it comes off easiest when cold. I did so in my basement garage after the hydro turf had been cool all winter. Some have had good results from using ice to cool it before removal. I used plastic paint scrapers to lift the corners then pulled as much as I could off in one piece. If it tore I would restart that process. Once it was off I used acetone to help remove leftover adhesive.

 

[Sarconen10]

@Bryan L What snaps are not covered by the Seadek in your boat? Looking to do marine tex on all the uncovered snaps so I don't have to worry about yellowing 5200

 

[Bruce]

@Bryan L What snaps are not covered by the Seadek in your boat? Looking to do marine tex on all the uncovered snaps so I don't have to worry about yellowing 5200

Does 5200 turn yellow? Mine is still white after three years.

 

[Sarconen10]

Does 5200 turn yellow? Mine is still white after three years.

I've read on multiple different threads that it yellows. And it says on the back of the tube there will be a slight discoloring from UV rays

 

[haknslash]

There's so much beautiful SeaDek in my life right now!

Thanks @JetBoatPilot

 

[Van T]

I'm wondering when mine is going to show up wanted to get it lasered can't figure out what to put on it or a hood boat name

 

[Bryan L]

@Bryan L What snaps are not covered by the Seadek in your boat? Looking to do marine tex on all the uncovered snaps so I don't have to worry about yellowing 5200

I have yet to do the cockpit. I have read somewhere on this site that one other person had three. I have noticed that the snaps are all over the place and not square or true to the non-skid. I may have a couple more than 3.

 

[Minh Nguyen]

Another question...how do you remove the seats to install the seadek that has the hole for the seat base? I'm stopping for the night. Already removed all the snaps and filled with 3m 5200. Got a few pads down also!

 

[Minh Nguyen]

Gotta stop or else I'm gonna get too drunk!

 

[Minh Nguyen]

Search seat removal and found that a member was doing the same project in March. Thanks swatski! Sorry for going off topic guys.

 

[swatski]

Gotta stop or else I'm gonna get too drunk!View attachment 47123

Looks nice and strait . Perfect job.